What is the minimum permitted static ground clearance of the vehicle, including the driver?
FS East 2018
Archive
Question browser
1065 matching questions
Suppose that 28 teams participate in the CV category on FS East 2018 and your team is one of them, there are 6 Business Finalist teams among them. The team with the highest points not reaching the finals has 67 points, your team received 59 points. What is your Business Plan Presentation Score?
FS East 2018
What is the steady-state output value of a PI controller for a non-zero DC input signal?
FS East 2018
What is the proper structure of the BOM?
FS East 2018
When the velocity of the vehicle is 126[km/h], the normal load on the tyre contact surface is double compared to load when it stands (v=0). Calculate the drag force acting on the vehicle at this velocity if its lift-to-drag ratio is 2,35[-] and its mass is 250[kg] (g=9,81[m/s^2])
FS East 2018
Which of the following CAN 2.0A messages have the highest priority (there are no stuffed bits or leading zeros and the frame ends after the data part, their data length may varies)?
FS East 2018
In which currency must the costs be displayed in the CBOM?
FS East 2018
Which is the maximum amount of energy stored in one HV accumulator segment?
FS East 2018
What is the input resistance of the following circuit? (R=400 Ohm, U1 = 10V, U2 = 8V)
FS East 2018
Our vehicle completes the Acceleration Event with 4[s] result. What is its velocity when it crosses the finish line, if we assume, that its acceleration is constant during the run?
FS East 2018
Which of the following is NOT considered as a "system" within the BOM?
FS East 2018
There is a wire with R resistance. After the wire is evenly streched to double length, what is the new resistance?
FS East 2018
Which of the following documents is directly evaluated during Engineering Design Event?
FS East 2018
When using a tab or bracket for a bolted joint in the primary structure, what should be the minimum distance from the center of the hole (radius 5.05 mm) to the nearest free edge of the tab or bracket? <br>Answer in mm and round to 2 decimal places.
FSG 2017
Due to electromagnetic interference a sensor signal is disturbed by a high frequency noise. To reduce this noise, you want to design a passive 1st-order Low-Pass Filter with a cut-off frequency at Fc=300Hz. What is the resulting phase shift of the sensor signal at F=150Hz?<br> Answer in degrees, the right sign and round to 2 decimal places.
FSG 2017
Your suspension expert told you, that the suspension travel changes by frequencies up to 220Hz. What is the theoretical minimum sample frequency you have to use for AD conversion of the sensor signal, such that all information of the continuous-time signal is captured?<br> Answer in Herz and round to 0 decimal places.
FSG 2017
Which is the total length of the Circuit of Barcelona-Catalunya?
FSS 2019
Who are the ESO's?
FSS 2019
How can you say in Spanish "Hello"?
FSS 2019
Which are the rules that FSS 2019 is following?
FSS 2019
Which is the maximum number of drivers allowed for each team?
FSS 2019
How many types of tyres are allowed for FSS 2019 competition?
FSS 2019
In the Skidpad event, which is the lenght of the inner circles diameter?
FSS 2019
How many points are awarded to every team that finishes endurance without DNF or DQ?
FSS 2019
Which are the dimensions allowed for the vehicle wheelbase?
FSS 2019
Which FSS Edition will take place on 2019?
FSS 2019
Concerning a given vector field v, which statement is correct?
FS East 2020
Which type of emergancy stop button is allowed to be used in the cockpit?
FS East 2020
Imagine that there is a Skidpad session. One of the drivers runs a full - skidpad scene, but at the end, the driver forgets to end the session and run a 3rd left circle instead of the normally 2 circles. What will be the result of this full - skidpad run?
FS East 2020
You would like to monitor the voltage of a LiPo cell by a mircocontroller. The voltage of the cell is always kept in the range of 3000...4000 mV. The microcontroller is supplied by 3.3V, the reference voltage of the 12 bit resolution ADC converter is 3V and the ground level for the ADC is the same as the cell's ground. The schematic of the system can be found below. Which one is the possible range of the ADC values?
FS East 2020